Echo gt 200r manual

Page 9: Contents After opening the carton, check for damage. Use the contents list to check for missing parts. Remove wing nut A , washer B , and bolt C. Snap the shield over the bearing housing. Use of alternative fuels may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement. Page Handling Fuel , will void the two-stroke engine warranty.

Keep movable parts of the attachment off the ground and away from objects that could become entangled or thrown. Page Starting Warm Engine The attachment should not move at idle, otherwise serious personal injury may result.

Purge Bulb Pump purge bulb C until fuel will be visible and flows freely in the clear fuel tank return line. If the task is not listed see your Echo dealer for repairs.

Tools required: 25 or 50 mm 1 or 2 in. Close choke Cold Start Position [ ]. This prevents dirt from entering the carburetor throat when the air filter is removed.

Brush accumulated dirt from air cleaner area. Tools Required: Locking tool, wrench, feeler gauge, soft wire brush. Remove spark plug and check for fouling, worn and rounded cen- ter electrode. Use the brush to remove dirt from the cylinder fins. Remove grass and leaves from the grid between the recoil starter and fuel tank.

To maintain proper engine operation and emission compliance above 1, feet MSL the carburetor may need to be adjusted by an authorized ECHO service dealer. Page Lubrication Every unit is run at the factory and the carburetor is set in compli- ance with emission regulations.

Carburetor adjustments, other than idle speed, must be performed by an authorized ECHO dealer. Before adjusting the carburetor, clean or replace the air filter and spark arrestor screen. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Width mm Height mm Engine Type Air cooled, two-stroke, single cylinder gasoline engine Bore Stroke Nettoyer les ailettes avec une brosse.

Page Lubrification Niveau 2. ECHO Print page 1 Print document 48 pages. To reduce injury risk to operator, helpers and bystanders, read and understand the Operator's and Safety manuals. Maintain a 15m 50 ft. Proper clothing and safety gear must be worn when operating a trimmer. Wear no-slip, heavy-duty work gloves to improve your grip on the blower handle. Gloves also reduce the transmission of machine vibration to your hands. Wear sturdy work shoes with nonskid soles:. Heavy protective clothing can increase operator fatigue, which may lead to heat stroke.

Schedule heavy work for early morning or late afternoon hours when temperatures are cooler. Exposure to vibration and cold may cause tingling and burning sensations followed by loss of color and numbness in the fingers.

The following precautions are strongly recommended because the minimum exposure which might trigger the ailment is unknown. Try to fill each day with jobs where operating the trimmer or other hand-held power equipment is not required. It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness and extreme pain in those areas.

Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years. Instead try to maintain a straight wrist position. Also, when grasping, use your whole hand, not just the thumb and index finger. Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment combination.

Read and comply with all safety instructions listed in this manual and safety manual. DO NOT operate unit if leaks are found. Replace if either is damaged or missing.

See Assembly for proper adjustment. Avoid contact during and immediately after operation. Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders.

Do not over reach. An Emission Control Label is located on the engine. The hour emission durability compliance period is the time span selected by the manufacturer certifying the engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual. The ECHO product you purchased has been partially assembled for your convenience. Due to packaging restrictions, installation of the plastic debris shield, nylon line head, and positioning of the front handle are necessary.

After opening the carton, check for damage. Use the contents list to check for missing parts. No assembly tools are needed and the nylon line head, plastic debris shield, and mounting hardware, shown in the contents list, are pre-assembled to the unit. Only the front handle may need to be re-positioned for comfortable operation. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up.

Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. GT R. Operate unit only if you are physically and mentally well. Hand Protection Wear no-slip, heavy-duty work gloves to improve your grip on the blower handle. Keep long hair away from engine and blower intake.

Retain hair with cap or net. Hot Humid Weather Heavy protective clothing can increase operator fatigue, which may lead to heat stroke. Repetitive Stress Injuries -- It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness and extreme pain in those areas. You can only view or download manuals with.

Sign Up and get 5 for free.